Loughborough University
Leicestershire, UK
LE11 3TU
+44 (0)1509 263171
Loughborough University

Loughborough University Institutional Repository

Please use this identifier to cite or link to this item: https://dspace.lboro.ac.uk/2134/33914

Title: Design and fabrication of a hydroformed absorber for an evacuated flat plate solar collector
Authors: Moss, Roger
Shire, Stan
Henshall, Paul
Eames, Philip C.
Arya, Farid
Hyde, Trevor
Keywords: Solar collector
Evacuated
Vacuum
Hydroform
Flow distribution
Issue Date: 2018
Publisher: © The Authors. Published by Elsevier
Citation: MOSS, R. ...et al., 2018. Design and fabrication of a hydroformed absorber for an evacuated flat plate solar collector. Applied Thermal Engineering, 138, pp. 456-464.
Abstract: © 2018 The Authors The concept of an evacuated flat plate collector was proposed over 40 years ago but, despite its professed advantages, very few manufacturers have developed commercial versions. The absorber is a key component of a flat plate collector: in the context of an evacuated panel, absorber design poses a number of technical challenges. A flooded panel absorber has been designed for use in evacuated flat plate solar collectors. The aim was to obtain higher efficiency, in a low out-gassing material, than would be possible using a conventional serpentine tube design. Initial plans for a micro-channel plate were modified when optimisation analysis showed that a flooded panel could achieve as good performance with easier fabrication. The absorber plate is made from hydroformed stainless steel sheets welded together and features an array of through-holes for the glass-supporting pillars with the square panel subdivided into two rectangles connected in series for ease of fabrication and better flow distribution. The coolant flow was modelled in Star-CCM+. FEM simulations based on tensile test data informed the choice of sheet thickness and weld radius around the holes to withstand the 1 bar pressure differential. Hydroforming is an effective method for producing sheet metal components, e.g. plates for heat exchangers or solar absorbers. As a thermal engineering experimental technique, the tooling is significantly cheaper than press tools since the mould does not need a matching die. In a research context, the ability to form plates in-house and explore profile and tooling options at low cost is very useful and might find application in other fields such as experimental heat exchangers. A hydroforming facility was built using 85 mm thick steel sheet and a 25 MPa hydraulic pump. This proved highly effective at forming 0.7 mm stainless steel sheet. A total of eight absorbers were fabricated and successfully leak tested using helium. Two variants were made: one kind for use in enclosures with a metallic rear tray, the other for enclosures with glass on both sides. The collector efficiency factor is estimated to be 3% higher than for commercial tube-on-plate designs.
Description: This is an Open Access Article. It is published by Elsevier under the Creative Commons Attribution 4.0 Unported Licence (CC BY). Full details of this licence are available at: http://creativecommons.org/licenses/by/4.0/
Sponsor: This work was funded by the the Engineering and Physical Sciences Research Council (EPSRC) as part of a collaborative programme between Warwick, Loughborough and Ulster universities, reference EP/K009915/1, EP/K010107/1 and EP/K009230/ 1
Version: Published
DOI: 10.1016/j.applthermaleng.2018.04.033
URI: https://dspace.lboro.ac.uk/2134/33914
Publisher Link: https://doi.org/10.1016/j.applthermaleng.2018.04.033
ISSN: 1359-4311
Appears in Collections:Published Articles (Mechanical, Electrical and Manufacturing Engineering)

Files associated with this item:

File Description SizeFormat
1-s2.0-S1359431117356478-main.pdfPublished version2.85 MBAdobe PDFView/Open

 

SFX Query

Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.